Rubber Components for Agricultural Machinery, Manufactured in India
Weather- and UV-resistant rubber components for farm equipment and irrigation systems, moulded to your drawing at our ISO 9001:2015 facility in Nashik, India.
COMPONENTS WE SUPPLY FOR AGRICULTURE
Engineered to Spec, Not to Catalogue
We don’t stock generic parts. Each component is produced against your drawing or an OEM sample — compound, hardness and geometry matched to outdoor service and the contamination it sees rather than picked from a catalogue.
Bushes & Bushings
Silent-block, pivot and shackle bushes for linkages, hitches and implement mounts
- Bonded and unbonded variants
- Natural rubber — best abrasion resistance of the eight compounds we mix
- Bore and OD to drawing
- Long-run batch consistency
Anti-Vibration Mounts
Cab, engine and gearbox mounts for tractors and self-propelled machinery
Bellows & Boots
Dust boots and protective covers for hydraulic rams, linkages and control rods
Gaskets
Valve, housing and tank gaskets for irrigation and fluid-handling assemblies
O-Rings
Hose connector, coupling and hydraulic seals across implements and irrigation
Pads, Stoppers & Caps
Hitch pin buffers, bump stops, cab floor mats and port caps
WHERE OUR COMPONENTS ARE USED
Built into machinery that works outdoors.
Tractors & self-propelled machinery
Cab mounts, engine isolation and pivot bushes rated for continuous outdoor service. Shaft seals for PTO drives, gearboxes and wheel hubs.
Irrigation systems
Hose connector seals, valve gaskets and sprayer diaphragms in weather-resistant compounds.
Implements & linkages
Hitch pin buffers, pivot bushes and protective boots for three-point linkages and towed implements.
Spraying & fluid handling
Diaphragms and seals selected for compatibility with agricultural chemicals and fertiliser solutions. Send the chemical and its concentration — a compound that holds against a dilute spray may not hold against the concentrate it is mixed from.
BUILT FOR AGRICULTURE CONDITIONS
Rubber that survives sun, water and grit.
Agricultural machinery sits outdoors year-round. Compound choice is driven by UV and ozone exposure, chemical contact and abrasive contamination rather than indoor service assumptions.
UV & Ozone Resistance
EPDM for components in continuous outdoor exposure — −40 °C to +140 °C, 40 to 90 Shore A — where general-purpose rubber perishes. Ozone resistance is one of the tests we run in-house, so a weathering specification can be checked before release rather than after a season in the field.
Abrasion & Contamination
Natural rubber — the best abrasion resistance of the eight compounds we mix — with sealed geometries for soil, grit and organic contamination. We supply moulded components — bushes, boots, seals and mounts — and rubber sheet lining for hoppers, chutes and tanks.
Temperature Swing
Compounds selected to stay flexible across seasonal extremes rather than a narrow operating band — EPDM −40 to +140 °C, neoprene −40 to +120 °C, natural rubber −20 to +90 °C. Below −20 °C natural rubber stiffens, and a linkage bush that was compliant in summer will not be on a cold start.
Shock & Vibration
Mount geometry tuned for rough-terrain shock loading rather than smooth-running industrial duty. Send the supported mass, the mounting orientation and the disturbing frequency — rate is set by geometry and hardness together, and a mount specified from hardness alone is a guess.
CUSTOM ENGINEERING
We match your machine spec, not the other way around.
Margo operates dedicated tooling capability for custom rubber components. Send us your OEM drawing, existing part, or equipment make and model — we reverse-engineer and produce to your specification.
- OEM drawing and sample matching
- Custom mould tooling in-house
- Rubber-to-metal bonding in-house — bonded bushes and mounts
- Compound selection by application, not by catalogue grade
- Pre-production sample approval before volume release
- Long-run production with consistent batch quality
Nashik, Maharashtra, India
ISO 9001:2015 certified manufacturing facility · certificate 09111526A
QUALITY & CERTIFICATION
Every batch. Every shipment.
Margo Rubber Products holds ISO 9001:2015 certification — certificate 09111526A, issued by Integral Certification Ltd and valid to 21 February 2027. Our quality management system covers incoming raw material inspection, in-process control and outgoing batch documentation. An IATF 16949:2016 upgrade is in progress, targeted for completion by the end of 2026.
Quality Management System
Certified quality management covering all production and inspection processes. Certificate 09111526A, valid to 21 February 2027; documentation available on request.
Drawing-Matched Production
Every component produced against a controlled drawing revision. No substitutions without approval.
Full Material Traceability
Raw material certificates and batch records retained per shipment. Available to agriculture buyers on request.
EXPORT SUPPLY
Direct supply from Nashik to agricultural equipment makers in East Africa, Australia and the UK.
Margo Rubber Products exports agricultural machinery components directly to equipment manufacturers, with full export documentation managed from Nashik. Components are produced against your controlled drawing revision, with pre-production sample approval available before volume release.
- EXPORT DOCUMENTATION
- Commercial invoice, packing list, certificate of origin, ISPM-15 fumigation certificate where timber packaging is used
- FREIGHT ROUTING
- Sea and air freight via established forwarders, ex-works Nashik or FOB Nhava Sheva
- COMMUNICATION
- English-language correspondence and technical support
- PAYMENT TERMS
- Discussed per order — TT and LC accepted
India → Export Markets
Direct OEM supply chain from Nashik, Maharashtra
- Australia
- United Kingdom
- Kenya
- Tanzania
- United States
Buyers are responsible for confirming applicable import duties for their specific order. Where timber packaging is used, consignments are shipped with ISPM-15 treated and marked pallets and a fumigation certificate. Kenya and Tanzania both require pre-shipment verification of conformity (PVoC) through an approved inspection body before departure — we supply the technical file and arrange inspection at the Nashik facility.
FREQUENTLY ASKED QUESTIONS
Questions from agricultural equipment buyers.
Which compound suits continuous outdoor exposure?
EPDM is the usual choice for weather-exposed components, for its UV and ozone resistance across −40 °C to +140 °C. Natural rubber blends are used where abrasion resistance matters more than weathering, at −20 °C to +90 °C. Ozone resistance is tested in-house before release.
Can you supply components resistant to agricultural chemicals?
Compound selection is driven by the specific chemistry in contact. Send the chemical, concentration and service temperature and we will recommend a compound. Send the concentrate as well as the diluted spray — a compound that holds against a field dilution may not hold in the mixing tank.
What is the minimum order quantity?
We supply in bulk. The minimum run is 10,000 pieces per part number, per compound, or quoted against the part where geometry or tooling makes that unrealistic. Prototype and first-article lots sit outside the minimum. Lead time is confirmed with the quotation, from approved drawing and approved sample.
Do you produce protective boots and bellows?
Yes. Bellows and boots are quoted against convolution count, free and compressed length, diameter, flex-cycle target and service temperature. We hold the geometry and the compound; the cycle life is proved by your rig or a third-party laboratory, and we will support that test.
Can you match an existing worn part?
Yes. Send the physical sample or the equipment make and model and we will produce a drawing and confirm compound selection. A worn part measures smaller than it was made — we dimension to the original intent, not to the wear, and confirm the result with you before tooling.
Are you certified, and do you meet automotive-style supplier requirements?
We hold ISO 9001:2015 — certificate 09111526A, issued by Integral Certification Ltd, valid to 21 February 2027. An IATF 16949:2016 upgrade is in progress, targeted for completion by the end of 2026. ISO 14001 and ISO 45001 are targeted for 2027. Documentation is available on request.
Ready to specify agricultural components from the manufacturer?
Send us your drawing, part number, or equipment make and model. Our team will confirm compound selection, tooling status, and lead time.