Margo Rubber Products

GUIDE · RUBBER COMPONENTS

Rubber Components Explained: How O-Rings, Oil Seals, Bushes and Diaphragms Are Made and Where They Are Used

Most machines rely on small rubber parts that nobody sees: the O-ring that stops a valve leaking, the bush that keeps a motor from shaking its frame, the grommet that protects a cable where it passes through steel. This guide covers eleven of them, all moulded or extruded at Margo's plant in Vilholi, Nashik: what each part is, how it is made, why it is needed and where you will find it, in industry and in the appliances in your home.

Published 20 November 2026

The eleven parts at a glance

PartWhat it doesHow it is madeTypical places it is used
O-ringSeals a joint between two partsCompression or injection mouldingPumps, valves, hydraulics, water purifiers, pressure cookers
Food-grade O-ringSeals where the product is eaten or drunkMoulding in a food-contact grade compoundDairy, bottling, beverage dispensers, food machinery
Static oil sealSeals oil in a housing where nothing rotatesMouldingGearbox covers, compressor housings, engine covers
Metal bonded oil sealSeals oil around a rotating shaftMoulding with a metal case bonded in the same cureGearboxes, axles, motors, pumps, washing machine drums
Rubber profileSeals or cushions along a lengthExtrusion and continuous cureDoors, windows, cabinets, refrigerators, ovens, buses
GrommetProtects a cable or pipe passing through a panelMouldingVehicle wiring, panels, appliances, control cabinets
Rubber bushLocates a part and absorbs vibrationMoulding, often bonded to a metal sleeveSuspensions, motor mounts, tractors, pumps
Rubber cushion bushCushions shock in a coupling or bearing mountMouldingPin-bush couplings, propeller-shaft bearings, pump drives
Rubber support padCarries a load and stops vibration and noiseCompression mouldingAC outdoor units, compressors, machines, truck bodies
DiaphragmFlexes to pump, meter or control a fluidMoulding, plain or with fabric reinforcementDosing pumps, valves, regulators, sprayers, purifiers
Rubber sealing (gaskets and seals)Seals flat faces, lids and doorsMoulding, extrusion or cutting from sheetFlanges, enclosures, lids, appliance doors

How rubber parts are made: the common steps

Every part in this guide starts the same way, whatever its final shape.

  1. Compounding. Raw polymer is mixed with fillers, oils, curing agents and protective chemicals into a compound. Margo mixes its eight compounds in-house: NBR, EPDM, FKM, silicone, AEM, neoprene, natural rubber and SBR. The compound decides what the finished part can survive: oil, heat, water, ozone or wear.
  2. Tooling. A steel mould, or for profiles a die, is cut to the part drawing. Margo cuts its own tools in-house.
  3. Shaping and curing. Heat and pressure turn the soft compound into elastic rubber, a step called vulcanisation or curing. This is done either in a mould (moulding) or as a continuous length (extrusion).
  4. Post-cure and finishing. Some compounds, such as silicone and FKM, are baked again in an oven to stabilise their properties. Excess rubber at the mould split line, called flash, is removed by cryogenic deflashing or by trimming.
  5. Inspection. Parts are checked for size against ISO 3302-1 tolerance classes and for hardness, and the compound is tested for tensile strength, compression set and ageing.

The three moulding methods

  • Compression moulding: a measured piece of compound is placed in the open mould and the press closes on it. Suited to thick sections and larger parts such as pads, buffers, mounts and large gaskets.
  • Transfer moulding: the compound is pushed from a chamber into a closed mould through small channels. Suited to parts with metal inserts and finer detail.
  • Injection moulding: heated compound is injected into a closed mould. Suited to high volumes of smaller, precise parts.

Extrusion

For profiles, cords and tubes, the compound is forced through a shaped die and cured continuously as it comes out. The result is a length with the same cross-section all the way along, which is then cut to size or joined into a closed frame.

O-rings

What it is. A ring of rubber with a round cross-section. It sits in a groove and is squeezed between two parts, and that squeeze seals the joint.

How it is made. O-rings are moulded in multi-cavity moulds, many at a time, then deflashed so the parting line does not leave a leak path. Large rings can be made from extruded cord, cut and vulcanised at the joint. Margo moulds them to AS568, ISO 3601, JIS B2401 and DIN 3771 sizes, or to your drawing.

Why it is needed. An O-ring is the simplest, cheapest way to seal a joint against liquid or gas, and it works under pressure in both directions.

Where it is used.

  • Industry: hydraulic and pneumatic cylinders, pumps, valves, fuel systems, refrigerant valves, compressors and pipe couplings.
  • Appliances: water purifier filter housings and taps, pressure cooker safety valves, mixer and juicer jars, coffee machines, washing machine water inlets and gas stove fittings.

Food-grade O-rings

What it is. An O-ring moulded in a compound chosen for contact with food or drink, usually silicone or EPDM, often in white, blue or red so a broken piece is easy to see.

How it is made. The same moulding process as any O-ring, in a compound selected for the product, the temperature and the cleaning cycle. Margo moulds food-grade O-rings on request. Margo holds no food-contact certificate for any compound, so food-contact compliance stays with the equipment maker's approval.

Why it is needed. Standard black compounds can taint food or break down under hot cleaning and steam. A food-grade compound is chosen so the seal survives the cleaning cycle without contaminating the product.

Where it is used.

  • Industry: dairy and brewery plant, bottling and filling lines, sanitary pipe couplings, food processing machinery and pharma process equipment.
  • Appliances: water dispensers, coffee machines, juicers, blenders and kitchen storage lids.

Static oil seals

What it is. A seal that keeps oil inside a housing where the parts do not move against each other: a cover, a plug or a joint. It usually has a rubber-covered outer diameter and no garter spring.

How it is made. Moulded in an oil-resistant compound, most often NBR, or FKM or AEM where the oil runs hot.

Why it is needed. Covers and plugs on oil-filled housings need a seal that grips the bore, does not shrink or swell in oil, and stays tight through heat cycles for years.

Where it is used.

  • Industry: gearbox and engine covers, compressor housings, hydraulic power packs, pump end covers.
  • Appliances: refrigerator and AC compressors, and oil-filled motor housings.

Metal bonded oil seals

What it is. A rotary oil seal with a steel case or insert bonded to the rubber. The rubber lip presses on the turning shaft, held in place by a garter spring, and keeps oil in and dirt out.

How it is made. The metal case is cleaned and prepared, coated with a primer and a cover coat matched to the compound, and placed in the mould. The rubber is moulded around it and bonded to it in the same cure, so there is no glued joint to fail. The garter spring is fitted afterwards. Margo moulds them to DIN 3760 and ISO 6194 profiles or to your drawing.

Why it is needed. The metal gives the seal a rigid, accurate press fit in the housing, so it does not turn or walk out. The rubber lip does the sealing on the moving shaft.

Where it is used.

  • Industry: car, tractor and two-wheeler gearboxes and axles, electric motors, pumps, compressors and industrial gearboxes.
  • Appliances: washing machine drum bearings, mixer grinder motors and pump sets.

Rubber profiles

What it is. A continuous length of rubber with a fixed cross-section: a bulb seal, a channel, a fin, a cord or a tube.

How it is made. Extruded through a die cut to the section drawing and cured continuously, then cut to length or joined at the corners into a closed frame. Sponge profiles are made by adding a blowing agent so the rubber foams as it cures. Margo extrudes in EPDM, NBR, FKM, silicone and neoprene.

Why it is needed. Doors, windows and lids need a seal that runs all the way round an edge, closes with a light push and springs back every time.

Where it is used.

  • Industry: bus, truck, rail coach and tractor cab doors and windows, building glazing, electrical panels and enclosures, refrigerated vans.
  • Appliances: refrigerator and freezer doors, oven and microwave door seals, dishwasher doors, display chillers and washing machine lids.

Grommets

What it is. A rubber ring or sleeve that fits into a hole in a panel so a cable, pipe or rod can pass through it.

How it is made. Moulded, with a groove that snaps into the panel hole. Margo makes open, blind, multi-hole, oval and bulkhead grommets from 6 mm panel hole upward, and to drawing above that.

Why it is needed. A sheet-metal edge cuts through a cable's insulation over time, especially when the machine vibrates. A grommet protects the cable, seals the hole against water and dust, and damps vibration.

Where it is used.

  • Industry: vehicle wiring harnesses and firewalls, control panels, switchgear, tractors and machinery.
  • Appliances: the back panels of washing machines, refrigerators and ACs where the power cord and pipes enter, and in fans, coolers and geysers.

Rubber bushes

What it is. A cylinder of rubber, often bonded to a metal inner sleeve, that sits between two parts that move slightly against each other.

How it is made. Moulded to the bore, outer diameter, length and hardness required. In a bonded bush, the steel sleeve is primed and the rubber is moulded and bonded to it in one cure.

Why it is needed. The rubber lets the joint flex and twist a little, while absorbing vibration and noise that would otherwise travel through the structure. It also needs no lubrication.

Where it is used.

  • Industry: vehicle suspensions and shackles, engine and transmission mounts, tractor linkages, pump and motor mountings, and water-lubricated bearings in submersible pumps.
  • Appliances: washing machine suspension and motor mounts, AC compressor mounts and cooler motors.

Rubber cushion bushes

What it is. A rubber bush whose main job is to cushion shock rather than locate a part. The best-known type sits on the pins of a pin-bush coupling between a motor and the machine it drives.

How it is made. Moulded, with the hardness set to the torque and the shock it has to carry.

Why it is needed. When a motor starts, the torque hits the coupling at once. The cushion bush takes that shock, allows for small misalignment between the two shafts and stops vibration passing from one machine to the other.

Where it is used.

  • Industry: pin-bush and jaw couplings on pumps, compressors, gearboxes and conveyors; the centre bearing cushion on truck, bus and tractor propeller shafts.
  • Appliances and equipment: domestic pump sets, generator sets and compressors.

Rubber support pads

What it is. A solid block or shaped pad of rubber that a machine or unit stands on.

How it is made. Compression moulded, usually in natural rubber, neoprene or EPDM, sized to the weight the pad carries.

Why it is needed. A running machine shakes. A support pad carries the weight, keeps the unit level, stops it walking across the floor and keeps vibration and noise out of the floor or wall.

Where it is used.

  • Industry: compressors, generator sets, pumps, machine tools, haul truck bodies, and vehicle body and cab mounts.
  • Appliances: AC outdoor units on wall brackets, washing machine feet, refrigerator compressor mounts, inverter and battery stands.

Diaphragms

What it is. A flexible rubber disc that moves back and forth to push a fluid, or that separates two chambers and flexes when the pressure changes.

How it is made. Moulded flat, rolling or convoluted. For higher pressure, layers of nylon, polyester or aramid fabric are bonded into the rubber during the cure. Simple flat diaphragms can be die-cut from sheet with no mould needed. The compound is chosen for the fluid the diaphragm touches on every stroke.

Why it is needed. A diaphragm moves fluid or senses pressure without a sliding seal, so nothing leaks past a piston and the fluid stays away from the moving parts.

Where it is used.

  • Industry: chemical dosing pumps, air-operated double-diaphragm pumps, weir valves, gas and pressure regulators, agricultural sprayers and brake chambers.
  • Appliances: water purifier pumps and valves, washing machine pressure switches, LPG regulators and gas geyser valves.

Rubber sealings: gaskets and seals

What it is. The general name for rubber parts that seal one surface against another: flat gaskets, flange gaskets, lid and door seals, washers and moulded seals of any shape.

How it is made. Moulded for shaped or thick parts, extruded and joined for long perimeters, or cut from rubber sheet for flat gaskets. The compound follows the medium: NBR for oil, EPDM for water and steam, silicone for heat, FKM for chemicals.

Why it is needed. No two metal faces are perfectly flat. A rubber gasket fills the gaps between them, so a joint stays tight under pressure, heat and vibration.

Where it is used.

  • Industry: pipe flanges, pump and valve bodies, engine and gearbox covers, EV battery packs, electrical enclosures and sanitary food pipework.
  • Appliances: pressure cooker gaskets, refrigerator and oven doors, water heater and purifier fittings, and tap washers.

Choosing the right compound

The same part can last for years or fail in weeks depending on the compound. As a starting point:

CompoundBest forAvoid
NBR (nitrile)Oil, fuel, hydraulic fluidWeather, ozone, steam
EPDMWater, steam, weather, brake fluidMineral oil and fuel
FKM (Viton)Aggressive chemicals, fuels, high heatSteam, cost-sensitive parts
Silicone (VMQ)Very high and very low temperatures, food-contact grades on requestWear and abrasion, rotating shafts
AEM (Vamac)Hot oil in engine and transmission baysSteam, fuel
Neoprene (CR)Refrigerants, moderate oil, flame-retardant gradesStrong oils and fuels
Natural rubberDamping, abrasion, vibration mountsOil, fuel, sunlight
SBRLow-cost static seals in waterOil and fuel

If you are not sure, send us the medium, the working temperature and the pressure, and we will recommend the compound for the part.

Frequently asked questions

  • What is the difference between moulded and extruded rubber parts?

    A moulded part is cured inside a closed steel mould, so it comes out as a finished shape: an O-ring, a grommet, a bush. An extruded part is pushed through a shaped die as a continuous length and cured, so it is a profile with the same cross-section all along: door seals, cords and channels. Extruded lengths can be cut and joined into closed frames.

  • What is a metal bonded oil seal?

    It is an oil seal with a steel case or insert that is bonded to the rubber during curing, not glued afterwards. The metal gives the seal a rigid, accurate press fit in the housing; the rubber lip, held against the shaft by a garter spring, does the sealing. They are used on gearboxes, axles, pumps and motors.

  • Are your food-grade O-rings certified for food contact?

    No. Food-grade O-rings are moulded on request in a compound chosen for the product, temperature and cleaning cycle, but Margo holds no food-contact certificate for any compound. Food-contact compliance stays with your equipment approval. Tell us the duty and we will propose the compound.

  • Which rubber compound should I choose?

    It depends on what the part touches and how hot it runs. NBR is the usual choice for oil and fuel, EPDM for water, steam and weather, FKM for aggressive chemicals and high heat, silicone for the widest temperature range, natural rubber for damping, and AEM for oil and heat together in engine bays. Send the medium, temperature and pressure and we will recommend one.

  • Can you make a part from a sample or a drawing?

    Yes. Every part in this guide is made to a customer drawing, a standard size reference or a worn sample. Moulded components are made in runs of at least 10,000 pieces per part number, per compound; extruded profile is priced per metre against your total run length.

Send us a drawing, a sample or just a description of where the part goes, and we will come back with the compound, the process and a quotation.