
Automotive O-Rings Moulded in Volume in India
O-rings for fuel, transmission, cooling, A/C and filler-cap seals, moulded in Nashik to AS568, ISO 3601, JIS B2401 and DIN 3771, or cut to your drawing, for vehicle makers and their Tier 1 and Tier 2 suppliers.
- AS568 · ISO 3601 · DIN 3771
- 30–90 Shore A
- 5 compounds
Margo Rubber Products moulds automotive O-rings at 30 to 90 Shore A, depending on the compound, in AEM, EPDM, FKM, NBR and silicone, to AS568, ISO 3601, JIS B2401 and DIN 3771. Tolerance follows the standard and the cross-section. Sizes outside the catalogue are cut to your drawing. Minimum run 10,000 pieces per part number, per compound; installed capacity 5 million parts a month.
AUTOMOTIVE O-RINGS WE MOULD
Standard sizes and drawing sizes.
Catalogue sizes run on existing tools; anything else is cut to print in our own tool room.

01
O-rings
AS568, ISO 3601, JIS B2401 and DIN 3771 sizes, or cut to your drawing.
View product
02
Filler cap O-rings
Oil and coolant filler cap seals that re-seat on every opening.
View product
03
Rubber oil seals
Shaft seals in DIN 3760 and ISO 6194 sizes, single and double lip.
View product
04
Wiring harness grommets
Open, blind, multi-hole and oval grommets for harness and firewall pass-throughs.
View product
COMPOUND BY SYSTEM
One ring, five possible compounds.
The same cross-section fails in weeks or lasts the vehicle's life depending on the compound. We choose it from the medium and temperature.
Fuel and oil
NBR for mineral oil and fuel to +120 °C; FKM for fuel blends and hot oil to +250 °C.
Coolant and A/C
EPDM for coolant, water and brake fluid; silicone for dry heat and wide-range static seals.
Volume and spare capacity
Installed capacity is 5 million parts a month against about 1.5 million in current production. The minimum run is 10,000 pieces per part number, per compound.
Checked through the run
Every mixed batch is checked, every run at set-up and every half hour, and every despatch lot for dimensions and hardness. Target rejection is under 1%; on-time delivery is over 99%.
WHERE OUR O-RINGS ARE FITTED
Static and slow-moving seals across the vehicle.
Fuel system
Injector, fuel rail, pump and filter O-rings in NBR or FKM.
Transmission and engine
Under-bonnet, sensor, dipstick and transmission O-rings in AEM, NBR or FKM.
Cooling and A/C
Hose connector and coolant-pipe O-rings in EPDM.
Filler caps
Oil and coolant filler cap seals that re-seat on every opening.
FREQUENTLY ASKED QUESTIONS
Questions from automotive buyers.
Which standards do your automotive O-rings follow?
AS568, ISO 3601, JIS B2401 and DIN 3771. Tolerance follows the standard and the cross-section. A size outside those catalogues is cut to your drawing in our own tool room, and a first-article sample is approved before volume release.
Can you mould O-rings in high volume for an automotive supplier?
Yes. The minimum run is 10,000 pieces per part number, per compound, and installed capacity is 5 million parts a month against about 1.5 million in current production. Quotation in 48 hours; production in three to four weeks from drawing approval.
Do you make Viton (FKM) O-rings for fuel systems?
Yes. FKM, the material sold under the Viton name, is rated to +250 °C and is our choice for fuel blends and hot synthetic oil. For mineral oil and fuel below +120 °C, NBR does the job at a lower price.
MORE FOR AUTOMOTIVE BUYERS
Automotive rubber parts by part and location
- Automotive rubber components: overview
- Automotive rubber bushes
- Automotive oil seals
- Automotive rubber grommets
- Automotive rubber pads & stoppers
- Automotive rubber profiles
- Rubber parts for Tier 2 suppliers
- Automotive rubber parts in Pune
- Automotive rubber parts in Aurangabad
- Automotive rubber parts in Nashik
Send the O-ring size and the system it seals.
ID, cross-section, standard, fluid, temperature and annual volume. We reply within 48 hours with a compound and a quotation.
