
Automotive Rubber Bushes for OEMs, Tier 1 & Tier 2
Suspension, engine mounting, silent-block, torque rod and cushion bushes, moulded to your drawing in Nashik for vehicle makers and the Tier 1 and Tier 2 suppliers who build their assemblies.
- Bonded and unbonded
- 45–75 Shore A
- AEM · NBR · NR · EPDM
Margo Rubber Products moulds automotive rubber bushes in 8–20 mm bore by 20–40 mm OD for silent blocks, 10–30 by 25–60 mm for insulation bushes and 12–40 by 30–80 mm for linkage bushes, at 45 to 75 Shore A, with dimensions held to ISO 3302-1 class M1 to M4. AEM covers −40 to +175 °C under the bonnet. Minimum run 10,000 pieces per part number; installed capacity 5 million parts a month.
AUTOMOTIVE BUSHES WE MOULD
Bushes for suspension, engine and body mounting.
Every bush is made to your drawing or an OEM sample. Hardness is set on the drawing, because hardness sets the rate.

01
Rubber bushes & silent blocks
Silent-block, insulation, linkage and cushion bushes, bore and OD to drawing.
View product
02
AEM insulation bush
Engine and transmission insulation bush in AEM, for heat and oil under the bonnet.
View product
03
Suspension bump stop
Commercial-vehicle suspension bump stop, moulded to the OEM sample.
View product
04
Bumper stopper
Bumper and tailgate stoppers that take the closing load without marking paint.
View product
SIZES, HARDNESS AND COMPOUNDS
What goes on the drawing.
Bore, outside diameter, length, hardness and compound decide how a bush behaves in the vehicle. Send them, or send the part, and we confirm each before tooling.
AEM for heat and oil
AEM holds −40 to +175 °C, continuous to about +160 °C, where engine oil, heat and ozone act together. Natural rubber suits a cool suspension position; NBR suits oil splash.
Rate set by hardness
Durometer runs 45 to 75 Shore A. Isolation only begins above about 1.4 times the system natural frequency, so the rate is matched to the mounting, not to a catalogue softness.
Volume and spare capacity
Installed capacity is 5 million parts a month against about 1.5 million in current production. The minimum run is 10,000 pieces per part number, per compound.
Checked through the run
Every mixed batch is checked, every run at set-up and every half hour, and every despatch lot for dimensions and hardness. Target rejection is under 1%; on-time delivery is over 99%.
| Bush type | Bore (mm) | Outside diameter (mm) | Typical position |
|---|---|---|---|
| Silent block | 8–20 | 20–40 | Suspension arm, link |
| Insulation bush | 10–30 | 25–60 | Engine, transmission, cab |
| Linkage bush | 12–40 | 30–80 | Torque rod, shackle, spring eye |
WHERE OUR BUSHES ARE FITTED
From the suspension arm to the cab mount.
Suspension and chassis
Silent-block, shackle and spring eye bushes for control arms, leaf springs and stabiliser links.
Engine and transmission
AEM insulation bushes and torque rod bushes where heat and oil end a natural rubber part.
Cab and body
Cushion bushes and support pads that isolate a cab, bracket or panel from road vibration.
Two-wheeler and commercial vehicle
Swing-arm, handlebar and cab-mount bushes in volumes from 10,000 pieces per part number.
FREQUENTLY ASKED QUESTIONS
Questions from automotive buyers.
Do you make bonded and unbonded automotive bushes?
Yes. Unbonded bushes are moulded rubber alone. Bonded bushes are cured onto a steel, stainless, aluminium or brass sleeve that is degreased, grit-blasted, treated and primed first, and the bond is tested to ASTM D429. Both are made to your drawing at our Nashik plant.
What volumes can you supply for a Tier 2 bush programme?
The minimum run is 10,000 pieces per part number, per compound. Installed capacity is 5 million parts a month against about 1.5 million in current production, so a new bush programme has room. Send the drawing and annual volume and we quote within 48 hours.
Which compound should an engine mounting bush use?
AEM where the bush sits near the engine: it holds −40 to +175 °C and resists engine oil and heat ageing. Natural rubber gives the best fatigue behaviour in a cool, dry suspension position. NBR suits oil splash below +120 °C. We propose the compound against the mounting position on your drawing.
MORE FOR AUTOMOTIVE BUYERS
Automotive rubber parts by part and location
- Automotive rubber components: overview
- Automotive oil seals
- Automotive O-rings
- Automotive rubber grommets
- Automotive rubber pads & stoppers
- Automotive rubber profiles
- Rubber parts for Tier 2 suppliers
- Automotive rubber parts in Pune
- Automotive rubber parts in Aurangabad
- Automotive rubber parts in Nashik
Send the bush drawing and your annual volume.
Bore, OD, length, hardness and position, or the existing part. We reply within 48 hours with a compound recommendation, tooling plan and quotation.
