
Automotive Rubber Grommets for Harness & Body Suppliers
Wiring harness, firewall, bulkhead and body-panel grommets, moulded in Nashik for harness makers, body-shop suppliers and vehicle assembly lines. Open, blind, multi-hole and oval, in any of eight compounds.
- Open · blind · multi-hole
- 6–50 mm holes
- EPDM · NBR · silicone
Margo Rubber Products moulds automotive grommets sized from the panel hole and panel thickness: 6–12 mm holes take a 1.0–1.6 mm panel, 12–25 mm holes take 1.2–2.0 mm, and 25–50 mm holes take 1.6–3.0 mm. Open, blind, multi-hole and oval grommets come in that range; holes above 50 mm and bulkhead grommets are cut to print. Minimum run 10,000 pieces per part number.
AUTOMOTIVE GROMMETS WE MOULD
Sized from the hole and the panel.
A grommet that is a fraction too thick for the panel pops out on the line; one too thin leaks. We size the groove from your panel drawing.

01
Wiring harness grommets
Open, blind, multi-hole and oval grommets for harness and firewall pass-throughs.
View product
02
3-pin hole pad
Multi-hole grommet pad that seals three wires through one panel opening.
View product
03
Internal-fit grommet
Push-in grommet that grips a panel hole from inside.
View product
04
Dust boots & gaiters
Boots for linkages, steering and driveshafts, Ø10 to Ø150 mm.
View product
GROMMET SIZING
Panel hole, panel thickness, compound.
Three numbers size a grommet. The compound follows what it sees: weather, oil or heat.
Compound
EPDM for weather and water at the firewall and body; NBR where oil or fuel splash reaches; silicone near the exhaust and turbo.
Fit on the line
Groove width matched to panel thickness so the grommet seats by hand, stays put and seals around the harness.
Volume and spare capacity
Installed capacity is 5 million parts a month against about 1.5 million in current production. The minimum run is 10,000 pieces per part number, per compound.
Checked through the run
Every mixed batch is checked, every run at set-up and every half hour, and every despatch lot for dimensions and hardness. Target rejection is under 1%; on-time delivery is over 99%.
| Panel hole (mm) | Panel thickness (mm) |
|---|---|
| 6–12 | 1.0–1.6 |
| 12–25 | 1.2–2.0 |
| 25–50 | 1.6–3.0 |
| Above 50, bulkhead | Cut to print |
WHERE OUR GROMMETS ARE FITTED
Every place a wire or pipe passes a panel.
Firewall and bulkhead
Harness pass-throughs that keep water, fumes and noise out of the cabin.
Doors and tailgate
Door and tailgate harness grommets that flex with every opening.
Engine bay
Sensor, pipe and cable grommets in NBR or silicone for oil and heat.
Lamps and switches
Multi-hole pads and switch grommets for lamp and electrical connectors.
FREQUENTLY ASKED QUESTIONS
Questions from automotive buyers.
Do you supply grommets to wiring harness makers?
Yes. Harness makers are typical Tier 2 buyers for us. We mould open, blind, multi-hole and oval grommets to the harness drawing, in volumes from 10,000 pieces per part number, with installed capacity of 5 million parts a month.
Which rubber is best for an automotive firewall grommet?
EPDM in most vehicles: it handles weather, water and engine-bay heat to about +140 °C. NBR where oil or fuel can reach the grommet, and silicone near the exhaust or turbo where the temperature runs higher.
Can you copy a grommet from a sample?
Yes. Send the physical grommet or the panel drawing. We measure it, propose a compound and hardness, cut the tool in-house and send a first-article sample for approval before volume production.
MORE FOR AUTOMOTIVE BUYERS
Automotive rubber parts by part and location
- Automotive rubber components: overview
- Automotive rubber bushes
- Automotive oil seals
- Automotive O-rings
- Automotive rubber pads & stoppers
- Automotive rubber profiles
- Rubber parts for Tier 2 suppliers
- Automotive rubber parts in Pune
- Automotive rubber parts in Aurangabad
- Automotive rubber parts in Nashik
Send the panel hole and the harness drawing.
Hole size, panel thickness, the number and size of wires or pipes, and your annual volume. We reply within 48 hours with a quotation.
