
Automotive Rubber Profiles & Extruded Seals
Windscreen glazing rubber, edge trim, door, hatch and channel seals and solid cords, extruded in Nashik to a profile drawing or sample for vehicle, bus and commercial-vehicle body builders.
- ±0.2 mm critical dimensions
- EPDM · neoprene · silicone
- Cut lengths or coils
Margo Rubber Products extrudes automotive rubber profiles to ±0.2 mm on the critical dimensions, recorded to ISO 3302-1 class E1 to E3, in EPDM, FKM, NBR, neoprene and silicone at 40–85 Shore A, across −60 to +250 °C. EPDM edge trim covers −40 to +140 °C for sun, rain and ozone. Pricing is per metre against your total run length.
AUTOMOTIVE PROFILES WE EXTRUDE
Seals by the metre.
Profiles are extruded to your section drawing and supplied in cut lengths, coils or joined frames.

01
Windscreen glazing rubber
Extruded glazing profile that holds and seals a fixed rear windscreen.
View product
02
Rubber edge trim
All-rubber U-profile that covers a panel edge and seals behind it.
View product
03
Rubber profiles & cords
Door, hatch and channel seals and solid cords extruded to a profile drawing.
View product
04
Dust boots & gaiters
Boots for linkages, steering and driveshafts, Ø10 to Ø150 mm.
View product
TOLERANCE AND COMPOUND
Held on the section that seals.
Each tolerance is set by the section and recorded to ISO 3302-1 class E1 to E3.
Weather and sun
EPDM is the default for doors, glazing and edges: −40 to +140 °C with sun, rain and ozone.
Oil and heat
NBR where the profile sees oil or fuel; neoprene for weather with oil splash; silicone on a hot panel.
Volume and spare capacity
Installed capacity is 5 million parts a month against about 1.5 million in current production. The minimum run is 10,000 pieces per part number, per compound.
Checked through the run
Every mixed batch is checked, every run at set-up and every half hour, and every despatch lot for dimensions and hardness. Target rejection is under 1%; on-time delivery is over 99%.
WHERE OUR PROFILES ARE FITTED
Glass, doors, hatches and edges.
Glazing
Rear windscreen and fixed-glass glazing rubber for cars, buses and cabs.
Doors and hatches
Door, hatch and service-panel seals for commercial vehicles and special-purpose bodies.
Edges
All-rubber edge trim that covers a cut panel edge and seals the gap behind it.
Cords and channels
Solid cords and channels for sealing grooves and cable runs.
FREQUENTLY ASKED QUESTIONS
Questions from automotive buyers.
What tolerance can an automotive rubber profile hold?
±0.2 mm on the critical dimensions of an extruded profile, with each tolerance set by the section and recorded to ISO 3302-1, class E1 to E3. Non-critical dimensions follow the wider class for that section.
Do you supply profiles to bus and commercial-vehicle body builders?
Yes. Glazing rubber, door and hatch seals and edge trim go to vehicle and body builders, including special-purpose vehicles such as Minerva Special Purpose Vehicle. Pricing is per metre against your total run length.
Can you match a profile from a sample?
Yes. Send a short length of the existing profile or the section drawing. We cut the die, propose a compound and hardness, and send a sample length for approval before the run.
MORE FOR AUTOMOTIVE BUYERS
Automotive rubber parts by part and location
- Automotive rubber components: overview
- Automotive rubber bushes
- Automotive oil seals
- Automotive O-rings
- Automotive rubber grommets
- Automotive rubber pads & stoppers
- Rubber parts for Tier 2 suppliers
- Automotive rubber parts in Pune
- Automotive rubber parts in Aurangabad
- Automotive rubber parts in Nashik
Send the section drawing and the total length.
The profile section or a sample, the compound or where it fits, and the metres per year. We reply within 48 hours with a die plan and a per-metre price.
