
Automotive Oil Seals for Tier 1 & Tier 2 Suppliers
Rotary shaft seals for gearboxes, crankshafts, wheel hubs, steering and pumps, moulded in NBR, FKM, AEM, EPDM and silicone at our plant in Nashik, in DIN 3760 and ISO 6194 sizes or to your drawing.
- DIN 3760 · ISO 6194
- NBR · FKM · AEM
- Metal-cased and rubber-covered
Margo Rubber Products moulds automotive oil seals in NBR for mineral oil, fuel and hydraulic fluid from −30 to +120 °C, and in FKM up to +250 °C for fuel and aggressive chemistry, in DIN 3760 or ISO 6194 sizes. EPDM is used for water, steam and brake fluid, never petroleum oil. Minimum run 10,000 pieces per part number, per compound; quotation in 48 hours.
AUTOMOTIVE OIL SEALS WE MOULD
Pick by the medium, then the temperature.
A shaft seal fails on the wrong compound before it fails on anything else. Tell us what the lip touches and how hot it runs.

01
Rubber oil seals
Shaft seals in DIN 3760 and ISO 6194 sizes, single and double lip.
View product
02
NBR oil seals
The default for mineral oil, fuel and hydraulic fluid, −30 to +120 °C.
View product
03
FKM oil seals
For fuel, hot oil and aggressive chemistry, rated to +250 °C.
View product
04
Filler cap O-rings
Oil and coolant filler cap seals that re-seat on every opening.
View product
COMPOUNDS AND STANDARDS
The compound follows the fluid.
Seals are moulded in five compounds. The table is where each one belongs in a vehicle.
Heat
NBR to +120 °C, AEM to about +160 °C continuous, FKM to +250 °C. A seal run above its compound's range hardens and leaks.
Fluid
NBR for mineral oil and fuel, FKM for fuel blends and hot synthetic oil, EPDM for coolant and brake fluid only.
Volume and spare capacity
Installed capacity is 5 million parts a month against about 1.5 million in current production. The minimum run is 10,000 pieces per part number, per compound.
Checked through the run
Every mixed batch is checked, every run at set-up and every half hour, and every despatch lot for dimensions and hardness. Target rejection is under 1%; on-time delivery is over 99%.
| Compound | Range | Typical position |
|---|---|---|
| NBR | −30 to +120 °C | Gearbox, axle, wheel hub, steering |
| AEM | −40 to about +160 °C continuous | Crankshaft and engine-side seals |
| FKM | up to +250 °C | Fuel system, hot synthetic oil |
| EPDM | water, steam, brake fluid | Coolant pump, brake system |
WHERE OUR SEALS ARE FITTED
Every shaft that leaves a housing.
Engine
Crankshaft front and rear seals, camshaft and valve stem seals.
Transmission and axle
Gearbox input and output seals, differential and wheel hub seals.
Pumps and steering
Water pump, oil pump and power-steering shaft seals.
Two-wheeler
Fork, crankcase and gear-shift seals in high-volume runs.
FREQUENTLY ASKED QUESTIONS
Questions from automotive buyers.
Do you make metal-cased oil seals for automotive use?
Yes. We mould rubber onto a prepared metal case, the skeleton or metal-bonded oil seal, and also make rubber-covered seals where the housing bore needs a rubber OD. Sizes follow DIN 3760 or ISO 6194, or your drawing for a non-standard shaft.
NBR or FKM for a gearbox oil seal?
NBR for a gearbox on mineral oil running below +120 °C, which covers most manual and commercial-vehicle gearboxes. FKM where the oil is synthetic and runs hot, or where the seal sees fuel. FKM costs more, so we specify it only where the temperature or fluid calls for it.
Can you supply oil seals in volume to a Tier 2 assembler?
Yes. The minimum run is 10,000 pieces per part number, per compound, and installed capacity is 5 million parts a month. Every despatch lot is checked for dimensions and hardness. Send the shaft size, housing bore, fluid and temperature and we quote within 48 hours.
MORE FOR AUTOMOTIVE BUYERS
Automotive rubber parts by part and location
- Automotive rubber components: overview
- Automotive rubber bushes
- Automotive O-rings
- Automotive rubber grommets
- Automotive rubber pads & stoppers
- Automotive rubber profiles
- Rubber parts for Tier 2 suppliers
- Automotive rubber parts in Pune
- Automotive rubber parts in Aurangabad
- Automotive rubber parts in Nashik
Send the shaft, bore and the fluid.
Shaft diameter, housing bore, width, fluid, temperature and annual volume, or the existing seal. We reply within 48 hours with a compound and a quotation.
